You are here

Composter Operation and Management

Filed Under:
Publication Number: P3231
View as PDF: P3231.pdf

Mississippi Board of Animal Health logo.

Composting is the most widespread method for proper and complete decomposition of poultry carcasses. The materials needed (poultry carcasses, litter or alternative carbon sources, and perhaps water) are readily available on every commercial poultry farm. Availability of cost-share funds to offset composter facility construction costs has contributed to an increase in the use of composting. However, attention to management is essential for success. Failure to properly manage the system will create odors and flies and attract unwanted scavengers and other vermin to the site. Proper management is vital to avoid nuisance complaints. Orderly loading of ingredients is critical for efficient compost activity.

Static bin composters are generally one of two types:

1. A series of various-sized bins constructed of treated lumber set on a concrete slab with a roof overhead (Figure 1). The slab prevents material from seeping into soil or groundwater, the walls keep the compost contained, and the roof protects the material from the elements.

Two divided bins composed of lumber with an open top and front. The bins are covered by a roof above.
Figure 1. Static bin composter.

2. One long bin (or alleyway) also set on a slab and covered by a roof (Figure 2).

A look down the alleyway between the lumber sides of the composter. The slab is concrete and there is a roof covering the composter.
Figure 2. Alleyway composter.

Regardless of type, ingredients should be layered into the composter as illustrated in Figures 3 and 4.

  • Place an initial layer of 8–12 inches of fresh litter on the concrete slab floor. This litter will supply bacteria to start the process and will also help absorb carcass fluids or excess water that may be added to the composter.
  • Next, add a layer of bird carcasses. Arrange the carcasses in a single layer side by side, touching each other. Place carcasses no closer than 6 inches to the walls of the compost bin. Carcasses placed too near the walls will not compost as rapidly because of lower temperatures there and may cause odorous liquids to seep from the compost.
  • Next, add a layer of litter. This layer should be twice as thick (8–10 inches) as the layer of carcasses underneath. If only a partial layer of birds is needed for a day’s mortality, the portion used must still be covered with litter. The rest of that layer can be used with subsequent mortality in the coming days.
  • After completing the initial layer, add subsequent layers of carcasses and litter/bulking material until a height not exceeding 5–6 feet is reached. The top layer will be a cap of 8–10 inches of litter. A height of 5–6 feet with adequate porosity and moisture levels is not a fire hazard. Keep in mind, however, the potential for spontaneous combustion, and monitor temperatures throughout the composting process. Excessive height can induce higher compost temperatures that exceed 170°F and increase the chance of spontaneous combustion. Additional carbon/bulking material may need to be added to better facilitate the decomposition process with birds larger than 8.5 pounds.
  • In-vessel or rotary drum composters (Figure 5) are the latest innovation in composter technology. These systems use controlled air infusion and simplified aeration techniques to decrease the time and daily management needed to compost material. However, the same principles apply as with bin/alleyway composting, and proper management is critical to success.
Figure 3. Side view of layers in a compost bin. The bin is 6–7 feet wide and 5–6 feet high. A concrete slab is at the lowermost level. On top of that is a 10- to 12-inch layer of litter. Then, a single layer of birds is alternated with 6–8 inches of litter. Finally, there is a 10- to 12-inch cap of litter at the top covering the material. Note that there are 6–8 inches of space between the bird carcasses and the sidewall on all four sides. The temperature in the middle of the bin should be between 140 and 160 degrees Fahrenheit.
Figure 3. Side view of layers in a compost bin. The bin is 6–7 feet wide and 5–6 feet high. A concrete slab is at the lowermost level. On top of that is a 10- to 12-inch layer of litter. Then, a single layer of birds is alternated with 6–8 inches of litter. Finally, there is a 10- to 12-inch cap of litter at the top covering the material. Note that there are 6–8 inches of space between the bird carcasses and the sidewall on all four sides.
Figure 4. Side view of compost at an angle in an alleyway composter. Width may be 12–18 feet and height should not exceed 5–6 feet. A concrete slab is at the lowermost level. Leave 6–8 inches of space between bird carcasses and the sidewalls on all sides.
Figure 4. Side view of compost at an angle in an alleyway composter. Width may be 12–18 feet and height should not exceed 5–6 feet. A concrete slab is at the lowermost level. Leave 6–8 inches of space between bird carcasses and the sidewalls on all sides.
An in-vessel or rotary drum composter underneath a metal roof. The composter is a large metal cyclinder resting on a green metal stand.
Figure 5. In-vessel or rotary drum composter.

Static bin composters with both primary and secondary bins are more labor-intensive because, once a smaller primary bin is full, it needs to sit for roughly 2 weeks. During this time, microbes break down roughly half the carcass material. However, they eventually run short of oxygen and the material has to be turned into the secondary bin for the process to be completed. After 2 weeks in the secondary bin, carcass material will be decomposed if temperature and moisture levels are correct. Therefore, it may take 5–8 weeks or more from the time you start to fill a bin until you have finished compost. Once finished, the compost material is ready to spread as a soil amendment, similar to chicken litter.

Troubleshooting Guide for Poultry Carcass Composting

Problem/Symptom

Probable Cause

Suggestions

Improper temperature

Too dry (<40% moisture)

Too wet (>60% moisture)

Improper C:N ratio

Improper mixing of ingredients

Adverse environment

Add water

Add bulking material and turn

Evaluate and adjust bulking material

Layer ingredients properly

Ensure adequate cover over top

Failure to decompose

Improper C:N ratio

Carcasses layered too thickly

Carcasses too close to outside edge

Evaluate and adjust bulking material

Single-layer the carcasses

Maintain minimum of 6 inches between carcasses and outside edges

Odor

Too wet

Too low C:N ratio

Inadequate cover between layers and on top

Add bulking material and turn

Evaluate and adjust bulking material

Use 6–8 inches of cover between layers and 10–12 inches over the top

Flies

Too wet

Poor sanitation conditions

Failure to reach proper temperature

Inadequate cover between layers and on top

Add bulking material and turn

Avoid leaching from pile

Assess C:N ratio; layer properly

Use 6–8 inches of cover between layers and 10–12 inches over the top

Scavenging animals

Inadequate cover over carcasses

Use 6–8 inches of cover between layers and 10–12 inches over the top

Avoid initial entry with fence or barrier

Use 6–8 inches of cover between layers and 10–12 inches over the top

Scavenging animals

Inadequate cover over carcasses

Use 6–8 inches of cover between layers and 10–12 inches over the top Avoid initial entry with fence or barrier


Publication 3231 (POD-05-21)

By Tom Tabler, PhD, Extension Professor, Poultry Science; Jessica Wells, PhD, Assistant Clinical/Extension Professor, Poultry Science; and Nikki Jefcoat, Poultry Division Director, Mississippi Board of Animal Health.

Department: Poultry Science
Print Friendly, PDF & Email

The Mississippi State University Extension Service is working to ensure all web content is accessible to all users. If you need assistance accessing any of our content, please email the webteam or call 662-325-2262.